WETEC

Solinst

415 12V Submersible Pump


Short, lightweight 12 V submersible pump with a controller for groundwater purging and sampling.

  • Sampling depth as much as 36.5 m (120 ft) below ground surface
  • Flow rates up to 13.5 L/min (3.6 US gpm) in shallow conditions
  • Fits inside nominal 2" OD Sched. 40 or 80 PVC pipe
  • Flow adjusted with a single dial on the 12V Pump Controller
Quantity
1

Overview

The Solinst Model 415 12V Submersible Pump provides an efficient means of purging and obtaining groundwater samples from monitoring wells. The 12V Submersible Pump and 12V Pump Controller are lightweight, portable, and easy to set up, deploy and operate. The pump is capable of pumping groundwater from 36.5 m (120 ft) below ground surface, with flow rates up to 13.5 L/min (3.6 US gpm) in shallow conditions. Its short (6" nominal) design fits easily down wells that are not straight or plumb, without hang-ups. The pump cable connects to the 12V Pump Controller, which clips to a 12 V power source, and the flow rate is adjusted with a single dial.

Typical applications

  • High and low-flow groundwater sampling for general chemistry
  • High purge rates when sampling using a three volume purge protocol
  • Performing constant head tests in environments with high K (hydraulic conductivity)

Key Features

  • Very simple to operate and adjust from high to low flow rates, with a single dial on the 12V Pump Controller
  • Sampling depth as much as 36.5 m (120 ft) below ground surface; flow rates up to 13.5 L/min (3.6 US gpm) in shallow conditions
  • Smooth, short (6" nominal) pump design avoids getting stuck in wells that aren't straight or plumb
  • Fits inside nominal 2" OD Sched. 40 or 80 PVC pipe
  • LED lights on the Controller indicate high or low battery voltage, proper battery connection, normal operation and maximum flow rate
  • Easy-to-reset circuit breaker, with no fuse to replace
  • Lightweight, compact, portable system
  • Optional dedicated 2" well cap for longer term projects
  • Optional 800M Mini Packer to isolate sampling zones and reduce purge volumes

Benefits

  • Simple flow control: Turn the dial on the 12V Pump Controller clockwise to increase the voltage to the Controller, which turns the pump motor faster and increases the flow rate.
  • High purge rates: Suited to three volume purge protocols.
  • Fits crooked wells: The pump's smooth, short design avoids hang-ups in wells that aren't straight or plumb.
  • Continuous operation: Can run continuously, as long as the pump is fully submerged during operation.
  • Portable power: Clips to almost any 12 V DC power source, such as a deep cycle AGM battery, or a vehicle or marine battery.
  • Dedicated option: A dedicated 2" well cap avoids cross-contamination and decontamination between wells on long-term monitoring projects.
  • Sediment protection: An optional disposable in-line water filter helps prevent sand ingress to the pump in environments with high suspended solids.

Specifications

SPECIFICATIONS

 

Sampling depth

As much as 36.5 m (120 ft) below ground surface

Flow rates

Up to 13.5 L/min (3.6 US gpm)

Pump cable lengths

25, 50, 75, 100 and 130 ft (7.5, 15, 23, 30 and 40 m)

Pump cable weight

3.5 kg (7.8 lbs) for the 130 ft (40 m) cable length

Wetted materials

ABS pump body
304 stainless steel motor, impeller and eyebolt
Polypropylene discharge outlet and hose barb
Nitrile/buna o-rings and seals
PVC jacket electrical wire

Pump size

4.78 cm OD x 13.97 cm long (1.88" x 5.5")

Pump weight

0.8 kg (1.8 lbs)

Controller size

33 cm x 13 cm x 17 cm (13" x 5" x 6.5")

Controller weight

3.4 kg (7.5 lbs)

Controller cable length

1 m (3.5 ft)

Power source

12V deep cycle 60 amp AGM battery or larger, or vehicle or marine battery
2.3 m (7.5 ft) power cord with alligator clips, for a 12 V DC source that can supply at least 45 amps at maximum draw

Voltage required

12.5 V to 15 V at source

Power draw

20 mA (dial OFF)
3 A (dial at 1) to 36 A (dial at MAX, 10)

Max. run time

Continuous, as long as the pump is fully submerged during operation

Sample tubing

3/8" (9.5 mm) ID LDPE tubing pushed onto the barbed fitting on the pump (sold separately)

Operating notes

The pump is designed to operate submerged only and for groundwater purging and sampling only
The Controller is water resistant but not waterproof: do not submerge
The Controller is only designed to work with the Model 415 12V Submersible Pump

 

 

ACCESSORIES AND POWER OPTIONS

 

800M Mini Packer Assembly

Isolates sampling zones and minimizes purge volumes
Connects directly to the pump intake with an adaptor

Disposable in-line water filter

For environments with high suspended solids, prevents sand ingress to the pump
Threads onto the pump intake

Tag Line

Reel-mounted marked cable for measured depth deployments (Model 103)

Dedicated 2" well cap

For long-term monitoring and to avoid cross-contamination or decontamination between wells
Includes a hanger bracket to support the pump weight and quick-connect fittings for the sample tubing
Access hole to fit a Solinst Water Level Meter or Levelogger
Adaptors to fit 4" wells available

Downloads

415 12V Submersible Pump Datasheet (EN) Download415 12V Submersible Pump Datasheet (EN)
415 12V Submersible Pump Operating Instructions (EN) Download415 12V Submersible Pump Operating Instructions (EN)